ASME A112.18.2

ASME A112.18.2

Plumbing waste fittings
Plumbing waste fittings
PLUMBING WASTE FITTINGS *** SAME AS CSA B125.2 ***
Plumbing waste fittings
Plumbing waste fittings
Plumbing waste fittings
Plumbing Fixture Waste Fittings

: In stock

Format
$90.00

Standard Details

Scope:
This Standard covers plumbing waste fittings of sizes NPS-2 and smaller.

This Standard does not cover

(a) plumbing supply fittings, which are covered by ASME A112.18.1/CSA B125.1;

(b) other devices (e.g., temperature-actuated in-line mixing valves), which are covered by CSA B125.3 or other plumbing product standards; and

(c) flexible water connectors under continuous pressure, which are covered by ASME A112.18.6/ CSA B125.6.

This Standard does not cover pipes and tubes or pipe and tube fittings that are downstream of the trap.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.

SI units are the units of record in Canada. In this Standard, the inch/pound units are shown in parentheses.

The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to U.S. gallons.

For information on the conversion criteria used in this Standard, see Annex A.



Organization: ASME International
Document Number: asme a112.18.2
Publish Date: 2015-01-01
Page Count: 50
Change Type: COMPLETE REVISION
Available Languages: EN
DOD Adopted: NO
ANSI Approved: YES
Most Recent Revision: YES
Current Version: YES
Status: Active

Publication Date: 01/01/2015 - Complete Document

Description :

This Standard covers plumbing waste fittings of sizes NPS-2 and smaller.

This Standard does not cover

(a) plumbing supply fittings, which are covered by ASME A112.18.1/CSA B125.1;

(b) other devices (e.g., temperature-actuated in-line mixing valves), which are covered by CSA B125.3 or other plumbing product standards; and

(c) flexible water connectors under continuous pressure, which are covered by ASME A112.18.6/ CSA B125.6.

This Standard does not cover pipes and tubes or pipe and tube fittings that are downstream of the trap.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.

SI units are the units of record in Canada. In this Standard, the inch/pound units are shown in parentheses.

The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to U.S. gallons.

For information on the conversion criteria used in this Standard, see Annex A.

 

Document Type : Complete Document

Language : English

Page Count : 50

Publication Date : 01/01/2015

Revision : 15

Status : Current

Title : Plumbing waste fittings

Publication Date: 01/01/2011 - Complete Document

Description :

This Standard covers plumbing waste fittings of sizes NPS-2 and smaller.

This Standard does not cover

(a) plumbing supply fittings, which are covered by ASME A112.18.1/CSA B125.1;

(b) other devices (e.g., temperature-actuated in-line mixing valves), which are covered by CSA B125.3 or other plumbing product standards; and

(c) flexible water connectors under continuous pressure, which are covered by ASME A112.18.6/ CSA B125.6.

This Standard does not cover pipes and tubes or pipe and tube fittings that are downstream of the trap.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

SI units are the units of record in Canada. In this Standard, the inch/pound units are shown in parentheses.

The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to U.S. gallons.

For information on the conversion criteria used in this Standard, see Annex A.

Document Type : Complete Document

Language : English

Page Count : 48

Publication Date : 01/01/2011

Revision : 11

Status : Historical

Title : Plumbing waste fittings

Publication Date: 06/01/2007 - Complete Document

Document Type : Complete Document

Page Count : 60

Publication Date : 06/01/2007

Revision : 05

Status : Historical

Title : PLUMBING WASTE FITTINGS *** SAME AS CSA B125.2 ***

Publication Date: 06/01/2007 - Amendment

Document Type : Amendment

Language : English

Page Count : 8

Publication Date : 06/01/2007

Revision : 05

Status : Historical

Title : Plumbing waste fittings

Publication Date: 11/01/2006 - Amendment

Description :

Preface

This is the first edition of ASME A112.18.2/CSA B125.2, Plumbing waste fittings.

This joint Standard was developed in response to an industry request for a Standard for testing plumbing waste fittings that would be acceptable in both Canada and the United States. Its coverage is restricted to plumbing waste fittings. Plumbing supply fittings located between the supply line stop and the terminal fitting are covered by ASME A112.18.1/CSA B125.1, Plumbing supply fittings. Devices not covered by this Standard or by ASME A112.18.1/CSA B125.1, e.g., temperature actuated in-line mixing valves and flexible connectors under continuous pressure, are covered by CSA B125.3, Plumbing fittings.

This Standard replaces ASME A112.18.2-2002, Plumbing Fixture Waste Fittings, and, together with ASME A112.18.1/CSA B125.1 and CSA B125.3, replaces CAN/CSA-B125-01, Plumbing Fittings.

The concept of harmonization for plumbing fittings arose in the early 1990s, when a free trade agreement between Canada, Mexico, and the United States began to be discussed. Standards development organizations (SDOs) were at the forefront of these discussions and an opportunity soon arose for those SDOs involved in setting requirements for plumbing products to establish a process for harmonization. However, the effort to develop a trinational Standard stalled until 2001, when ASME and CSA decided to develop a binational Standard for plumbing fixture fittings. Harmonization activities were undertaken by a Joint Harmonization Task Group (JHTG), in which the ASME and CSA plumbing fitting committees were equally represented. The responsibility for procedural matters and final approval of technical content was assumed by committees and teams at higher levels within each SDO. Initially, the JHTG's philosophy was to draft a Standard reflecting existing requirements in the applicable ASME and CSA Standards. This seemed a reasonable task, given that ASME and CSA had already been trying for many years to harmonize the requirements in their plumbing fitting Standards in response to constant requests for revision. There were only a few tests in the applicable ASME Standard that did not appear in its CSA counterpart, and vice versa (corrosion, swing spout strength, and intermittent shock, to name three). However, once the JHTG began to meet, its members realized that there was room for improvement in how both Standards dealt with current products and technologies. It was therefore agreed that the new Standard would not only harmonize the requirements of both existing Standards but also improve on them. The design requirements of this Standard, however, are generally similar to those of the Standards it replaces, which is understandable considering that plumbing waste fittings perform basically the same functions now that they did when the Standards being replaced were first developed.

This Standard was prepared by the ASME/CSA Joint Harmonization Task Group on Plumbing Fittings, under the jurisdiction of ASME Standards Committee A112 on Plumbing Materials and Equipment and the CSA Technical Committee on Plumbing Fittings. The CSA Technical Committee operates under the jurisdiction of the CSA Strategic Steering Committee on Plumbing Products and Materials. This Standard has been formally approved by ASME Standards Committee A112 and the CSA Technical Committee. ASME A112.18.2-2005 was approved as an American National Standard by the American National Standards Institute on February 14, 2005. CSA B125.2 will be submitted to the Standards Council of Canada for approval as a National Standard of Canada.

Document Type : Amendment

Language : English

Page Count : 6

Publication Date : 11/01/2006

Revision : 05

Status : Historical

Title : Plumbing waste fittings

Publication Date: 01/01/2005 - Base Document

Description :

This Standard covers plumbing waste fittings of sizes NPS-2 and smaller.

Plumbing supply fittings are covered by ASME A112.18.1/CSA B125.1.

Other devices, e.g., temperature-actuated in-line mixing valves and flexible connectors under continuous pressure, are covered by CSA B125.3 or other plumbing product Standards.

This Standard does not apply to pipes and tubes or pipe and tube fittings.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements. The purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements.

The values stated in either SI (metric) or yard/pound units are to be regarded as the standard. SI units are the units of record in Canada.

In this Standard, the yard/pound units are shown in parentheses. The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to US gallons.

For information on the conversion criteria used in this Standard, see Annex A.

Document Type : Base Document

Language : English

Page Count : 46

Publication Date : 01/01/2005

Revision : 05

Status : Historical

Title : Plumbing waste fittings

Publication Date: 07/01/2002 - Complete Document

Description :

This Standard establishes performance requirements and test methods for plumbing fixture waste fittings such as, but not limited to: bathtub waste and overflow drains; traps; trap wall adapters; fixture strainers and drains; pop-up assemblies; continuous waste assemblies and other tubular components.

Document Type : Complete Document

Language : English

Page Count : 20

Publication Date : 07/01/2002

Revision : 02

Status : Historical

Title : Plumbing Fixture Waste Fittings

Quick Add

$460.00
$297.00
$485.00

Please call 1-800-566-1677 for quotes on subscriptions

See More titles in ASME

See More titles in Designators