ASME A112.18.1

ASME A112.18.1

Plumbing supply fittings
Plumbing supply fittings
PLUMBING SUPPLY FITTINGS
Plumbing Fixture Fittings
Plumbing Fixture Fittings
Plumbing Fixture Fittings
Plumbing Fixture Fittings
PLUMBING SUPPLY FITTINGS

: In stock

Format
$130.00

Standard Details

This Standard covers plumbing supply fittings and accessories located between the supply stop and the terminal fitting, inclusive, as follows:

(a) automatic compensating valves for individual wall-mounted showering systems;

(b) bath and shower supply fittings;

(c) bidet supply fittings;

(d) clothes washer supply fittings;

(e) drinking fountain supply fittings;

(f) humidifier supply stops;

(g) kitchen, sink, and lavatory supply fittings;

(h) laundry tub supply fittings;

(i) lawn and sediment faucets;

(j) metering and self-closing supply fittings;

(k) shower heads, hand-held showers, and body sprays; and

(l) supply stops.

This Standard does not cover

(a) plumbing waste fittings, which are covered by ASME A112.18.2/CSA B125.2;

(b) other devices (e.g., temperature-actuated in-line mixing valves), which are covered by CSA B125.3 or other plumbing product Standards; and

(c) flexible water connectors under continuous pressure, which are covered by ASME A112.18.6/ CSA B125.6.

Except for push-fit fittings, this Standard does not cover pipes and tubes or pipe and tube fittings.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

SI units are the units of record in Canada. In this Standard, the inch/pound units are shown in parentheses

The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to U.S. gallons.

For information on the conversion criteria used in this Standard, see Annex A.

Organization: ASME International
Document Number: asme a112.18.1
Publish Date: 2012-01-01
Page Count: 72
Change Type: COMPLETE REVISION
Available Languages: EN
DOD Adopted: NO
ANSI Approved: NO
Most Recent Revision: YES
Current Version: YES
Status: Active

Publication Date: 01/01/2012 - Complete Document

Description :

This Standard covers plumbing supply fittings and accessories located between the supply stop and the terminal fitting, inclusive, as follows:

(a) automatic compensating valves for individual wall-mounted showering systems;

(b) bath and shower supply fittings;

(c) bidet supply fittings;

(d) clothes washer supply fittings;

(e) drinking fountain supply fittings;

(f) humidifier supply stops;

(g) kitchen, sink, and lavatory supply fittings;

(h) laundry tub supply fittings;

(i) lawn and sediment faucets;

(j) metering and self-closing supply fittings;

(k) shower heads, hand-held showers, and body sprays; and

(l) supply stops.

This Standard does not cover

(a) plumbing waste fittings, which are covered by ASME A112.18.2/CSA B125.2;

(b) other devices (e.g., temperature-actuated in-line mixing valves), which are covered by CSA B125.3 or other plumbing product Standards; and

(c) flexible water connectors under continuous pressure, which are covered by ASME A112.18.6/ CSA B125.6.

Except for push-fit fittings, this Standard does not cover pipes and tubes or pipe and tube fittings.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

SI units are the units of record in Canada. In this Standard, the inch/pound units are shown in parentheses

 The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to U.S. gallons.

For information on the conversion criteria used in this Standard, see Annex A.

Document Type : Complete Document

Language : English

Page Count : 72

Publication Date : 01/01/2012

Revision : 12

Status : Current

Title : Plumbing supply fittings

Publication Date: 01/01/2011 - Complete Document

Description :

This Standard applies to plumbing supply fittings and accessories located between the supply line stop and the terminal fitting, inclusive, as follows:

(a) automatic compensating valves for individual wall-mounted showering systems;

(b) bath and shower supply fittings;

(c) bidet supply fittings;

(d) clothes washer supply fittings;

(e) drinking fountain supply fittings;

(f) humidifier supply stops;

(g) kitchen, sink, and lavatory supply fittings;

(h) laundry tub supply fittings;

(i) lawn and sediment faucets;

(j) metering and self-closing supply fittings; and

(k) supply stops.

Plumbing waste fittings are covered by ASME A112.18.2/CSA B125.2.

Other devices, e.g., temperature-actuated in-line mixing valves and flexible connectors under continuous pressure, are covered by CSA B125.3 or other plumbing product Standards.

This Standard does not apply to pipes and tubes or pipe and tube fittings.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements.

The values stated in either SI (metric) or yard/pound units are to be regarded as the standard. SI units are the units of record in Canada.

In this Standard, the yard/pound units are shown in parentheses. The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to US gallons.

For information on the conversion criteria used in this Standard, see Annex A.

Document Type : Complete Document

Language : English

Page Count : 86

Publication Date : 01/01/2011

Revision : 11

Status : Historical

Title : Plumbing supply fittings

Publication Date: 11/01/2006 - Complete Document

Document Type : Complete Document

Page Count : 100

Publication Date : 11/01/2006

Revision : 05

Status : Historical

Title : PLUMBING SUPPLY FITTINGS

Publication Date: 11/01/2006 - Amendment

Description :

This Standard applies to plumbing supply fittings and accessories located between the supply line stop and the terminal fitting, inclusive, as follows:

(a) automatic compensating valves for individual wall-mounted showering systems;

(b) bath and shower supply fittings;

(c) bidet supply fittings;

(d) clothes washer supply fittings;

(e) drinking fountain supply fittings;

(f) humidifier supply stops;

(g) kitchen, sink, and lavatory supply fittings;

(h) laundry tub supply fittings;

(i) lawn and sediment faucets;

(j) metering and self-closing supply fittings; and

(k) supply stops.

Plumbing waste fittings are covered by ASME A112.18.2/CSA B125.2.

Other devices, e.g., temperature-actuated in-line mixing valves and flexible connectors under continuous pressure, are covered by CSA B125.3 or other plumbing product Standards.

This Standard does not apply to pipes and tubes or pipe and tube fittings.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements.

The values stated in either SI (metric) or yard/pound units are to be regarded as the standard. SI units are the units of record in Canada.

In this Standard, the yard/pound units are shown in parentheses. The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to US gallons.

For information on the conversion criteria used in this Standard, see Annex A.

Document Type : Amendment

Language : English

Page Count : 26

Publication Date : 11/01/2006

Revision : 05

Status : Historical

Title : Plumbing Fixture Fittings

Publication Date: 01/01/2005 - Base Document

Description :

This Standard applies to plumbing supply fittings and accessories located between the supply line stop and the terminal fitting, inclusive, as follows:

(a) automatic compensating valves for individual wall-mounted showering systems;

(b) bath and shower supply fittings;

(c) bidet supply fittings;

(d) clothes washer supply fittings;

(e) drinking fountain supply fittings;

(f) humidifier supply stops;

(g) kitchen, sink, and lavatory supply fittings;

(h) laundry tub supply fittings;

(i) lawn and sediment faucets;

(j) metering and self-closing supply fittings; and

(k) supply stops.

Plumbing waste fittings are covered by ASME A112.18.2/CSA B125.2.

Other devices, e.g., temperature-actuated in-line mixing valves and flexible connectors under continuous pressure, are covered by CSA B125.3 or other plumbing product Standards.

This Standard does not apply to pipes and tubes or pipe and tube fittings.

In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements.

The values stated in either SI (metric) or yard/pound units are to be regarded as the standard. SI units are the units of record in Canada.

In this Standard, the yard/pound units are shown in parentheses. The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.

All references to gallons are to US gallons.

For information on the conversion criteria used in this Standard, see Annex A.

Document Type : Base Document

Language : English

Page Count : 74

Publication Date : 01/01/2005

Revision : 05

Status : Historical

Title : Plumbing Fixture Fittings

Publication Date: 05/30/2003 - Complete Document

Description :

This Standard establishes general performance requirements and test methods for plumbing fixture fittings, accessories, other terminal fittings, and supply stops. It does not apply to conventional fittings such as nipples, elbows, tees, etc.

Document Type : Complete Document

Language : English

Page Count : 28

Publication Date : 05/30/2003

Revision : 03

Status : Historical

Title : Plumbing Fixture Fittings

Publication Date: 01/01/2000 - Complete Document

Description :

This Standard establishes general performance requirements and test methods for plumbing fixture fittings, other terminal fittings, supply stops, wastes, and traps. It does not apply to conventional fittings such as nipples, elbows, tees, etc.

Document Type : Complete Document

Language : English

Page Count : 28

Publication Date : 01/01/2000

Revision : 00

Status : Historical

Title : Plumbing Fixture Fittings

Publication Date: 01/01/1971 - Complete Document

Document Type : Complete Document

Page Count : 17

Publication Date : 01/01/1971

Revision : 71

Status : Historical

Title : PLUMBING SUPPLY FITTINGS

Quick Add

$423.00
$289.00
$485.00